Part Number: 9743 Epoxy Primer - Red
Aeroglaze® 9743 is a two-part epoxy primer designed for use on aluminum, metal, and prepared composite surfaces. Aeroglaze 9743 primer/tie-coat can be applied to scuff-sanded urethane top coats and epoxy primers. It is also used as a tie coat between scuff sanded weather worn coatings and new urethane topcoats.
Size: N/A
Unit of Measure: Can
Minimum Order Qty: 1
Manufacturer: LORD
Usually Ships: Request
Features and Specifications
Aeroglaze® 9743 is a two-part epoxy primer designed for use on aluminum, metal, and prepared composite surfaces. Aeroglaze 9743 primer/tie-coat can be applied to scuff-sanded urethane top coats and epoxy primers. It is also used as a tie coat between scuff sanded weather worn coatings and new urethane topcoats. Features and Benefits: Meets Military Performance Requirements of Mil-P-23377, Excellent Chemical and Corrosion Resistance, Lead and Chromate-free, VOC Compliant (310 gm/liter, 2.6 lbs/gal VOC). Limitations. For industrial/commercial use only. Must be applied by trained personnel only. Not to be used in residential applications. Not for consumer use. Four-hour workable pot life at 25°C (77°F). Mix only enough to be used in a four-hour period for ease of application and reduced waste. Maximum cure time before topcoating is 18 hours. Surface Preparation: For maximum corrosion protection and long service life, clean all substrates and properly prepare before priming.
EPOXY PRIMER COATING KIT (AEROGLAZE 9743)
EPOXY PRIMER COATING KIT (AEROGLAZE 9744)
PRIMER COATING (AEROGLAZE 9924)
Lord 506/19 is a general purpose, semi-flexible, heat resistant acrylic adhesive. Lord 506 acrylic adhesive bonds a wide variety of themoplastics and themoset plastics. (506/19)
Lord 7542 is a equal-mix two component urethane system. Lord 7542 adhesive bonds FRP, SMC, and other plastics with little surface preparation. This adhesive will also bond primed metals. Lord 7542 adhesive system is available in a range of working times to accommodate a wide variety of process requirements. (7542 A/B)
Lord 7545 is an equal-mix, two-component, paste urethane adhesive system. Lord 7545 adhesive is specifically formulated to be easily applied when dispensed from Lord-Pak hand-held cartridges. Lord 7545 adhesive bonds FRP, SMC, and other plastics with little surface preparation where bond strengths greater than the substrate are desired. This adhesive also bonds primed metals and various combinations of dissimilar substrates. Lord 7545 adhesive system is available in a range of working times to accommodate a wide variety of process requirements. (7545 A/B)
Aeroglaze® 9743 is a two-part epoxy primer designed for use on aluminum, metal, and prepared composite surfaces. Aeroglaze 9743 primer/tie-coat can be applied to scuff-sanded urethane top coats and epoxy primers. It is also used as a tie coat between scuff sanded weather worn coatings and new urethane topcoats. (9743 Epoxy Primer - Red)
Aeroglaze® 9924 is a two-part epoxy primer designed for use on aluminum, metal, and prepared composite surfaces. Aeroglaze 9924 primer/tie-coat can be applied to scuff-sanded urethane top coats and epoxy primers. It is also used as a tie coat between scuff sanded weather worn coatings and new urethane topcoats. (9924 Wash Primer)
Aeroglaze® 9924V wash primer (9924V)
PRIMER (9929 Epoxy Primer)
Aeroglaze® 9947 wash primer is designed for priming metal surfaces. It is particularly useful for priming nonferrous substrates such as aluminum and galvanized steel. Meets FDA Dry Bulk Food Regulation Title CFR, Paragraph 175.300. (9947 Wash Primer - Chromate-Free)
Aeroglaze® 9953 thinner is used to reduce Aeroglaze epoxy viscosity for spray applications. (9953)
Aeroglaze® 9958 thinner is used to reduce Aeroglaze primer and topcoat viscosities for spray applications. (9958)
Lord 204/19 acrylic adhesive bonds a wide variety of prepared or unprepared metals and plastics. Lord 204 acrylic adhesive replaces welding, riveting and other mechanical fastening methods. Also available in the No-Mix System by spraying, rolling, or brushing Lord Accelerator onto one or both surfaces. (204/19)
Sizes: 50ml cartridge, 200ml cartridge, Quart Kit (Qt kit contains 1qt 320 and 1 qt 322 for a total of 2 Quarts) (320/322)
Lord® 363 adhesive is a fast set, two-component epoxy adhesive system used to bond scuffed sheet molded compounds (SMC), wood, fiberglass reinforced plastics (FRP) and other plastics. This adhesive system can be either room temperature cured or heat cured for faster processing. (363 A/B)
Features and Benefits. Versatile - bonds unprepared metals with minimal substrate preparation: bonds difficult plastics such as polycarbonate and XENOY. Temperature Strength - performs at temperatures from -40 to +300 F (-40 to + 149 C). Environmental Resistant - resists dilute acids, alkalis, solvents, greases, oils, moisture and weathering; provides excellent resistance to UV exposure. Non-Sag - remains in position when applied on vertical or overhead surfaces, allowing for greater process flexibility. Lord 403/19: Work Time: 2-4 minutes. Handleable Bond: 4-6 minutes. Full Properties: 24 hours (403/19)
Sold: single 50 ml cartridge,case of (12) 50 ml cartridges, 375 ml cartridge grey w/GB, case of (12) 375 ml grey w/ GB (406/19)
Lord 410/19 . Work Time: 20-30 minutes. Handleable Bond: 60 minutes. Full Properties: 24 hours (410/19)
Available: Lot of (12) 4 oz bottles, lot of (4) Gallons. Price shown is your Lot charge. Lord 459T primer can be used in conjunction with Lord acrylic adhesives, urethane adhesives, epoxy structural adhesives, and cyanoacrylate adhesives, as well as with a variety of double sided tapes. (459T)
Lord 606 is a fast setting, acrylic adhesive used with Lord Accelerator 6 GB (glass beads) to bond composites including DCPD resin and modified DCPD resin based FRP (fiber reinforced plastic). Lord 606 adhesive can also cross-bond composites to many metals. (606/6)
NOTE: This product ships ‘Hazardous Freight‘. To accurately calculate shipping charges to your specific location, this product must be ordered by phone by calling us at 800-327-9504. (7701)
Two-Part Epoxy Primer (AEROGLAZE 9741)
Standard thinner for all Chemglaze coatings. A blend of ester and aromatic solvents. Normal use is 5 - 25%. (9951)
Lord 9986 Catalyst is normally used with A-Line and Z-Line coatings at 1-2%. It presents no pot life limitations if the coatings are not exposed to moisture. At higher loadings, no greatly increased cure rate is obtained and the danger of plasticization and adhesion failure is possible. (9986)
9995 is particularly effective with the V-Line and C-Line coatings, to increase cure time without drastically reducing pot life. It is also effective in A-Line and Z-Line coatings if 9986 proves insufficient. Weight concentrations of up to 3% with the Z-Line and 5-6% with A and C-Lines are acceptable. (9995)
Aeroglaze® A276 reflective polyurethane gives a hard,flexible, colorfast, non-chalking surface that is resistant to most acids, alkaline detergents, lubricants, and chemicals. (A276)
Lord Aeroglaze K3425 Gray Sandable Primer: For application on epoxy graphite or other plastic substrates or over a suitable primer on metal. (K3425)
Lord Aeroglaze Z302 is a Special Order product and there is a 50 Gallon minimum. Please call for pricing. (Z302)
Lord Aeroglaze Z306 Flat Black Absorptive Polyurethane (Z306)
(AP-134)
Lord Chemglaze 9944 wash primer is designed for priming metal surfaces. It is particularly useful for priming metal surfaces, especially for priming non-ferrous substrates such as aluminum and galvanized steel. (9944)
Lord Chemglaze A-Line coatings are designed for industrial maintenance applications. They provide a hard, colorfast surface that is resistant to attack by most acids, alkali, detergents, lubricating oils, solvents and chemicals. Chemglaze A-Line coatings have outstanding abrasion resistance and good exterior durability. (Chemglaze A-Line Aliphatic Polyurethane Coatings)
Chemglaze V-Line polyurethane coatings are used in product finishing applications on polyvinyl-chloride (PVC) and other plastics where maximum performance properties are needed. These coatings provide the highest possible combinations of abrasion resistance, wear properties and flexibility. Use Chemglaze V-Line coatings as protective coatings for vinyl, Mylar, ABS, FRP, and Noryl. (Lord Chemglaze V-Line Aliphatic Polyurethane Coatings for Plastics)
Chemglaze Z-Line coatings can be used on rigid substrates such as metals, concrete and wood, or on flexible substrates such as rubber, plastics, and leather. Because of their excellent resistance to wear, abrasion and chemicals, they are particularly useful in heavy industrial and aggressive atmospheres where protection is a prime consideration. These coatings are recommended for interior use since loss of gloss, yellowing and chalking will occur when exposed to sunlight. (Lord Chemglaze Z-Line Aromatic Polyurethane Coatings)
NOTE: This product ships ‘Hazardous Freight ‘. To accurately calculate shipping charges to your specific location, this product must be ordered by phone by calling us at 800-327-9504. Lord Chemlok® 459X is Available: Lot of (12) 1/2 pints, lot of (4) Gallons. Prices shown are your Lot price. (459X)
Lord Maxlok™ MX/T18 acrylic adhesive replaces welding, brazing, riveting and other mechanical fastening methods especially over a wide range of temperature environments subject to high impact or high peel loads. (MX/T18)
Lord Maxlok™ MX/T3 acrylic adhesive replaces welding, brazing, riveting and other mechanical fastening methods especially over a wide range of temperature environments subject to high impact or high peel loads. (MX/T3)
Sold: 50 ml cartridge*, 375 ml cartridge, case of (12) 50ml, case of (12) 375 ml cartridges *Note: your price for the single 50 ml cartridge includes (1) caulking gun adapter (#DP DK-119) (MX/T6)
Aeroglaze® Z307 black absorptive conductive polyurethane coating is primarily for application to substrates used on spacecraft. These applications include those where coatings must exhibit low outgassing characteristics while providing static dissipating and high thermal absorptivity properties. (Z307)
(Aeroglaze 9947)
Two-part epoxy primer (AEROGLAZE® 9741)
Aeroglaze® 9743, Two-Part Epoxy Primer (AEROGLAZE® 9743)
Aeroglaze® 9744 is a two-part epoxy primer designed for use on aluminum, metal, and prepared composite surfaces. Aeroglaze 9744 primer/tie-coat is applied to scuff-sanded urethane top coats and epoxy primers. It is also used as a tie-coat between scuff-sanded weather worn coatings and new urethane topcoats. (AEROGLAZE® 9744)
Aeroglaze® 9947 two-component wash primer is designed for priming metal surfaces, particularly nonferrous substrates such as aluminum. Primer may also be used on properly prepared steel and galvanized steel. (AEROGLAZE® 9947)
Aeroglaze® 9958 thinner is used to reduce viscosities of Aeroglaze wash primers and Aeroglaze polyurethane coatings for spray applications. (AEROGLAZE® 9958)
Aeroglaze® A276 coating is a reflective, moisture-curing polyurethane coating designed for product finishing applications on substrates used in aircraft and aerospace applications. Aeroglaze A276 coating cures to a high gloss white finish. (AEROGLAZE® A276)
For application on epoxy graphite or other plastic substrates or over a suitable primer on metal. Aeroglaze® K3425 primer/surfacer contains no inhibiting pigments and is not suitable in direct-to-metal applications. Color: Medium Gray. (AEROGLAZE® K3425)
Aeroglaze® M1433 elastomeric coating is a gray, twocomponent polyurethane coating designed for protecting radomes, antennae and leading edges of aircraft. Aeroglaze M1433 elastomeric coating functions exceptionally well in abrasive environments and is qualified to Military Specification MIL-PRF-85322. (AEROGLAZE® M1433)
Aeroglaze® Z306 coating is an absorptive polyurethane coating designed for application on substrates used in aerospace operations. These operations include those where coatings must exhibit low outgassing characteristics while providing high thermal absorptivity properties. Aeroglaze Z306 coating cures to a flat black finish. (AEROGLAZE® Z306)
Aeroglaze® Z307 coating is an absorptive, electrically conductive polyurethane coating designed for application on substrates used in aerospace operations. These operations include those where coatings must exhibit low outgassing characteristics while providing static dissipating and high thermal absorptivity properties. Aeroglaze Z307 coating cures to a flat black finish. (AEROGLAZE® Z307)
Chemglaze® 9951 thinner is used to reduce the viscosity of Chemglaze polyurethane coatings. It is formulated with a blend of ester and aromatic, urethane-grade solvents. (CHEMGLAZE® 9951)
Chemglaze® A-line coatings are moisture-curing, aliphatic polyurethane coatings designed for product finishing applications on many metal and rigid or semirigid plastic substrates. Chemglaze A-Line coatings are ASTM D-16 Type II oil-free products, and are available in clear, black and white. (CHEMGLAZE® A080)
Elastomeric Coating (CHEMGLAZE® M331/M201)
Chemglaze® V-line coatings are moisture-curing, aliphatic polyurethane coatings designed for product finishing applications on polyvinyl-chloride (PVC) and other plastics where maximum abrasion resistance, wear and flexibility properties are needed. Chemglaze V-Line coatings can also be used as protective coatings for vinyl, Mylar®, ABS, FRP, and Noryl®. (CHEMGLAZE® V209)
This product does not flow, does not dry, does not stick and enables a very good acoustic transmission. (UltraConductive Coating for LSP)
This product does not flow, does not dry, does not stick and enables a very good acoustic transmission. (UltraConductive Film for LSP)
(AEROGLAZE 9929)
(AEROGLAZE Z306)
THINNER (AEROGLAZE 9953)
POLYURETHANE COATING (AEROGLAZE Z307)
(AEROGLAZE 9700B)
EPOXY PRIMER (AEROGLAZE 9929A/B)
Aeroglaze® Z306 coating is an absorptive polyurethane coating designed for application on substrates used in aerospace operations. These operations include those where coatings must exhibit low outgassing characteristics while providing high thermal absorptivity properties. Aeroglaze Z306 coating cures to a flat black finish. (AEROGLAZE® Z306)
Elastomeric Coating (CHEMGLAZE® M331/M201)
Elastomeric Coating (CHEMGLAZE® M331/M201)
Aeroglaze® Z307 coating is an absorptive, electrically conductive polyurethane coating designed for application on substrates used in aerospace operations. These operations include those where coatings must exhibit low outgassing characteristics while providing static dissipating and high thermal absorptivity properties. Aeroglaze Z307 coating cures to a flat black finish. (AEROGLAZE® Z307)
Aeroglaze® Z306 coating is an absorptive polyurethane coating designed for application on substrates used in aerospace operations. These operations include those where coatings must exhibit low outgassing characteristics while providing high thermal absorptivity properties. Aeroglaze Z306 coating cures to a flat black finish. (AEROGLAZE® Z306)
Aeroglaze® Z307 coating is an absorptive, electrically conductive polyurethane coating designed for application on substrates used in aerospace operations. These operations include those where coatings must exhibit low outgassing characteristics while providing static dissipating and high thermal absorptivity properties. Aeroglaze Z307 coating cures to a flat black finish. (AEROGLAZE® Z307)
Aeroglaze® A276 coating is a reflective, moisture-curing polyurethane coating designed for product finishing applications on substrates used in aircraft and aerospace applications. Aeroglaze A276 coating cures to a high gloss white finish. (AEROGLAZE® A276)
